Hot Products

USD 0.57-0.58/Piece
USD 0.69-0.7/Piece
USD 0.6-1/Piece
USD 15.15-16/Piece
Top suppliers

Response Time


Response Rate


Keming Electronics Development Co., Ltd

Response Time


Response Rate


Product:Original&authentic Semiconductor, NXP,TI,ST,HIT,TOS,NS,ON,FSC,EL,HAR,ITS,NEC,JRC,SHARP,INFINEON,Sunlord,CJ,LRC,Arduino parts,etc.

Response Time


Response Rate


Product:Diodes,PIN Diodes,Power Diodes,Schottky Diodes,Zener Diodes
Shenzhen Ruijie Electronic Technology Co. Ltd.

Response Time


Response Rate


Product:Automobile Relay,Reed Relay,Power Relay,Tantalum Capacitor,Ceramic Capacitor
Shenzhen light Microelectronics Co., Ltd.
What is 2N4401 transistor and how does it work
/ 2018/6/21 9:36:08 / News

what is 2N4401 transistor

As is described in the 2N4401 PDF,the 2N4401 NPN transistor is designed for general purpose switching and amplifier applications. PNP complementary types are 2N4402 and 2N4403.

2N4401 transistor image

2N4401 Main attributes


Sillion NPN transistor

2N4401 Application:

Used for low frequency audio amplification circuit.

2N4401 Features:

current characteristics are good and the output power is large, which can be complementary to 2N4403.

Pb−Free Packages are Available*

2N4401 package:

TO-92 and etc.

2N4401 switching time equivalent test circuits

2N4401 switching time equivalent test circuits

2N4401 electrical characteristics

hFE: 100-300
fT: 250MHz
Parts Warranty: 90days

2N4401 Pinout

2N4401 pinout

In the above "2N4401 pinout" image,1 is emitter,2 is base,3 is collector.

2N4401 Maximum ranting

2N4401 Maximum ranting

Power dissipation:


Collector emitter voltage:


Collector base voltage:


Emitter base voltage:


Collector current:


2N4401 amplifier circuit

Amplifier is an electronic devices that can increase the power of a signal. It uses electric power form a power supply to increase the amplitude of a signal. So amplifier play an important role in boosting up the signal to required level and widely employed in audio applications.Transistor amplifiers can be built with ease and also cost effective that other types.In order to built one all you need is Transistor, power supply, some Resistors and Capacitors. For complex amplifier circuits go for this 200W subwoofer Amplifier. Let’s move in to the working of amplifier circuit using transistor .

2N4401 amplifier circuit

The above circuit uses a simple NPN Transistor Q1 2N4401 and powered by a 12v Supply. The resistor values R1,R2,R3,R4 and capacitor values C1,C2 plays major role in amplification of input signals. So fixing these values requires some simple math to meet our amplification requirements. First we need to fix the value of Collector resistor R3 based on the desired collector current and voltage.  Capacitor C2 of 1uF was added to remove the DC offset in the input signal and keep our circuit stable.

Since we need the Transistor to amplify both the negative and positive component of a signal ,it is advised to give Collector voltage Vc equals to 1/2Vcc that is 4.5v. Thereby using ohms we obtain the R3 value

R3 = (Vcc – Vc) / Ic

R3 = (9v – 4.5v) / 1mA = 4500 Ohm

4.7K is the standard value of resistor hence 4.7K is employed in the circuit.

The Current flowing through the Collector terminal will be equal to the current flowing through the emitter terminal Ic = Ie. Resistance in the emitter is already built into the transistor and it is called as transresistance, which is calculated as.

 R4 = 0.026V / Ie

 R4  = 0.026V / 1mA = 26 Ohm

The gain of the amplifier circuit can be calculated using the formula

 Gain = Rc / Re = R3 / R4

Since small resistance will create stability problem in circuit therefore we need to add our own resistance in the emitter terminal. We are going to use a 1K resistor in the emitter to provide stability in the amplifier circuit. But the increase in resistance will decrease the gain obtained and we are going to compromise it by adding a capacitor parallel to R4 forming a high pass filter.

Using high pass filter we can pass signals of assigned frequency. Here the RC values are selected in a way to permit signals of 300 Hz. This can be calculated by

 f = 1/( 2 x pi x R x C )

Substituting the R, f values we can obtain the C value

300 Hz = 1/(2 x 3.14 x 1000 x C)

C = 0.000020F or 20uF

Now Components at the Collector and Emitter terminals are fixed still we need to set R1 and R2 values for biasing transistor.

Transistor will switch on only if we apply voltage push at its base and this is equal to 0.6v for silicon transistor. The voltage at base of a transistor is 0.6v higher than the voltage at emitter so

Vb = Ve + 0.6V

Vb= 1v + 0.6v = 1.6v

So we are about to employ a voltage divider to supply the voltage to the base of the transistor. The Resistor values R1 and R2 can be calculated by  using the formula

Vout = R2 x Vin / ( R1 + R2 )

Rearranging these equations,

R1/R2 = ( Vin – Vout ) / Vout

 R1/R2 = ( 9v – 1.6v ) / 1.6v  = 4.6

Thus R1 needs to be 4.6 times greater than the R2 and approximating the values give R1 = 4.7K and R2 = 1K.

2N4401 switch circuit

In particular, we may use a 2N4401 general purpose transistor as a switch. A transistor has three terminals. The earliest transistor technologies were based on creating a sandwich of n and npn-type semi-conductor materials. These so-called npn or pnp bipolar junction transistors (BJT)'s are still used today. The 2N4401 is a BJT. The lefthand drawing in the following picture shows the electronic symbol used for an npn BJT. From this figure you will see that the three terminals for the transistor are referred to as the collector, emitter, and base terminals. The physical device is extremely small. It is a small cylinder that has one side flattened. The flattened side is used to help determine which of the three leads is the base, emitter, and collector. A drawing of the physical device is shown on the righthand side of the following picture.

2N4401 Transistor

Transistors can be connected in a way that allows a relatively small base current to either switch on or off a relatively large collector current. Such a connection is shown in following figure. In this figure, a 5 k-ohm resistor is connected in series to the base terminal of the transistor. The collector terminal is connected to the positive supply voltage of +9 volts and the emitter terminal is connected to the common anode of the 7-segment LED display. When the voltage level on the base terminal is low, then, the transistor switch is closed and a current flows from the nine volt supply, through the LED to ground. When the voltage level on the base terminal is high, then the switch is open and no current flows through the LED. The size of the emitter-collector current is controlled by the 100 ohm resistors of the LED driver circuit you designed in the last lab. Because of the small size of these resistors, the emitter-collector current is large when the transistor switch is closed and the LED's are bright. The base-emitter current is determined by the relatively large resistor (5 k-ohm) on the base terminal. Because of the large size of this resistor, the base-emitter current can be kept to low levels that can be tolerated by the MicroStamp11.

Schematic of Display Circuit

Relevant articles recommend

Contact Us


One to One Customer Service