The is a hex translator for converting F100K logic levels to TTL logic levels. Differential inputs allow each circuit to be used as an inverting, non-inverting or differential receiver. An internal reference voltage generator provides VBB for single-ended operation, or for use in Schmitt trigger applications. All inputs have 50k pull-down resistors. When the inputs are either unconnected or at the same potential the outputs will go LOW. When used in single-ended operation the apparent input threshold of the true inputs to 40mV higher (positive) than the threshold of the complementary inputs. The VEE and VTTL power may be applied in either order.Features
s Pin/function compatible with 100125 s Meets 100125 AC specifications s 50% power reduction of the 100125 s Differential inputs with built in offset s Standard FAST outputs s 2000V ESD protection to -5.7V operating range s Available to industrial grade temperature range
Order Number 100325QI 100325QC Package Number N24E V28A Package Description 24-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide 24-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-010, 0.400 Wide 28-Lead Plastic Lead Chip Carrier (PLCC), JEDEC MO-047, 0.450 Square 28-Lead Plastic Lead Chip Carrier (PLCC), JEDEC MO-047, 0.450 Square Industrial Temperature Range to +85�C)
Devices also available in Tape and Reel. Specify by appending the suffix letter "X" to the ordering code.Pin Names D5 Q0�Q5 Description Data Inputs Inverting Data Inputs Data Outputs
FAST is a registered trademark of Fairchild Semiconductor Corporation.
Storage Temperature (TSTG) Maximum Junction Temperature (TJ) VEE Pin Potential to Ground Pin VTTL Pin Potential to Ground Pin Input Voltage (DC) Voltage Applied to Output in HIGH State (with VCC = 0V) Current Applied to Output in LOW State (Max) ESD (Note 2) twice the rated IOL (mA)Case Temperature (TC) Commercial Industrial Supply Voltage (VEE) to +85�C
Note 1: The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum rating. The "Recommended Operating Conditions" table will define the conditions for actual device operation. Note 2: ESD testing conforms to MIL-STD-883, Method 3015.
VEE to -5.7V, VCC = GND, VTTL to +85�C (Note 3) Symbol VBB VIH VIL VOH VOL VDIFF VCM IIH IIL IOS IEE ITTL Parameter Output Reference Voltage Single-Ended Input HIGH Voltage Single-Ended Input LOW Voltage Output HIGH Voltage Output LOW Voltage Input Voltage Differential Common Mode Voltage Input HIGH Current Input LOW Current Output Short-Circuit Current VEE Power Supply Current VTTL Power Supply Current VCC - 2.0 VCC 0.5 350 Min Typ -1320 Max -870 -1475 Units �A mA VIN = VIH (Max), D0�D5 = VBB, D0�D5 = VIL (Min) VIN = VIL (Min), D0�D5 = VBB VOUT = GND (Note D0�D5 = VBB D0�D5 = VBB IVBB -2.1 mA Guaranteed HIGH Signal for All Inputs (with One Input Tied to VBB) Guaranteed LOW Signal for All Inputs (with One Input Tied to VBB) IOH -2.0 mA IOL 20 mA Required for Full Output Swing VIN = VIH (Max) or VIL (Min) Conditions
Note 3: The specified limits represent the "worst case" value for the parameter. Since these values normally occur at the temperature extremes, additional noise immunity and guardbanding can be achieved by decreasing the allowable system operating ranges. Conditions for testing shown in the tables are chosen to guarantee operation under "worst case" conditions. Note 4: Test one output at a time.
VEE to -5.7V, VCC = GND, VTTL = 0�C Symbol Parameter Min Max tPLH tPHL tPLH tPHL Propagation Delay Data to Output Propagation Delay Data to Output = +25�C Min 0.90 1.70 Max = +85�C Min 1.00 1.80 Max 4.00 4.80 Units ns Conditions 15 pF Figures 50 pF Figures 1, 3