Homedatasheet1N5353B

1N5353B Datasheet

Package Type : T-18, PD : 5.0W, VZ : 11V
Share:
Manufacturer

Description

Features, Applications
Features

Low profile package Built strain relief Glass passivated junction Low inductance For available tolerances � See Note1

Operating Temperature: C DC Power Dissipation: 5 Watts Power Derating: 40 mW/ C above 75 C Forward Voltage 1.0A: 1.2 Volts

Case: JEDEC DO-201AE , molded plastic over passivated junction. Terminals: Solder plated ,solderable per MIL-STD-750,

Method 2026. Standard Packaging 52 mm tape. Weight : 0.04 ounces , 1.1 gram (approx)
ELECTRICAL CHARACTERISTICS A=25 �J unless otherwise noted, VF=1.2 Max @ IF=1A for all types).
Nominal Zener Type No. (Note 1.) Voltage Vz @ IZT volts (Note 1N5387B 1N5388B

NOTE: 1. TOLERANCE AND VOLTAGE DESIGNATION - The JEDEC type numbers shown indicate a tolerance of 10% with guaranteed limits on only Vz, IR, Ir, and VF as shown in the electrical characteristics table. Units with guaranteed limits on all seven parameters are indicated by suffix "B" for 5% tolerance. 2. ZENER VOLTAGE (Vz) AND IMPEDANCE (ZZT & ZZK) - Test conditions for Zener voltage and impedance are as follows; Iz is applied 10 ms prior to reading. Mounting contacts are located from the inside edge of mounting clips to the body of the diode.(TA=25 �J ���J

3. SURGE CURRENT (Ir) - Surge current is specified as the maximum allowable peak, non-recurrent square-wave current with a pulse width, PW, of 8.3 ms. The data given in Figure 5 may be used to find the maximum surge current for a quare wave of any pulse width between 1 ms and 1000ms by plotting the applicable points on logarithmic paper. Examples of this, using the 6.8v and 200V zeners, are shown in Figure 6. Mounting contact located as specified in Note (TA=25 �J ���J 4. VOLTAGE REGULATION (�G Vz) - Test conditions for voltage regulation are as follows: Vz measurements are made at 10% and then 50% of the Iz max value listed in the electrical characteristics table. The test currents are the same for the 5% and 10% tolerance devices. The test current time druation for each Vz measurement 40 10 ms. (TA=25 �J ���J Mounting contact located as specified Note2. 5. MAXIMUM REGULATOR CURRENT (IZM) - The maximum current shown is based on the maximum voltage a 5% type unit. Therefore, it applies only to the B-suffix device. The actual IZM for any device may not exceed the value of 5 watts divided by the actual Vz of the device. �J at maximum from the device body.

APPLICATION NOTE: Since the actual voltage available from a given zener diode is temperature dependent, it is necessary to determine junction temperature under any set of operating conditions in order to calculate its value. The following procedure is recommended: Lead Temperature, TL, should be determined from: = �c LAPD LA is the lead-to-ambient thermal resistance (�J /W) and PD is the power dissipation. Junction Temperature, TJ , may be found from: + �G TJL �G TJL is the increase in junction temperature above the lead temperature and may be found from Figure 3 for a train of power pulses or from Figure 4 for dc power. �G TJL = �c JLPD For worst-case design, using expected limits of Iz, limits

of PD and the extremes of TJ(�G TJ) may be estimated. Changes in voltage, Vz, can then be found from: TJ �c VZ, the zener voltage temperature coefficient, is fount from Figures 2. Under high power-pulse operation, the zener voltage will vary with time and may also be affected significantly be the zener resistance. For best regulation, keep current excursions as low as possible. Data of Figure 3 should not be used to compute surge capability. Surge limitations are given in Figure 5. They are lower than would be expected by considering only junction temperature, as current crowding effects cause temperatures to be extremely high in small spots resulting in device degradation should the limits of Figure. 5 be exceeded.


Features

Parameters

Download DataSheet PDF View and Download


Manufacturer information

MICRO COMMERCIAL COMPONENTS
Warm Hint

What HQEW.NET can offer here?
1. www.hqew.net/product-data provides numerous and various electronic part data-sheet and technology document here., if it can't be shown, Please feel free to ask us for it.
2. www.hqew.net/news provides the latest information of the semiconductor industry or the electronics industry for you.
3. www.hqew.net provides verified suppliers and numerous electronic components for your demand and business.
Any questions you can contact us by email cs@hqew.net.
related datasheet
Browse Alphabetically: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Contact Us

+86-755-83536845

One to One Customer Service

17190417227