Homedatasheet24AA04

24AA04 Datasheet

I2C->4K to 8K
Share:
Manufacturer

Description

Features, Applications

Part Number 24AA04 24LC04B Vcc Range 1.8-5.5 2.5-5.5 Max Clock Frequency kHz(1) 400 kHz Note 1: 100 kHz for VCC <2.5V

Description

Temp Ranges I, E The Microchip Technology Inc. a 4 Kbit Electrically Erasable PROM. The device is organized as two blocks x 8-bit memory with a 2-wire serial interface. Low voltage design permits operation down to 1.8V with standby and active currents of only 1 �A and 1 mA respectively. The 24XX04 also has a page-write capability for to 16 bytes of data. The 24XX04 is available in the standard 8-pin PDIP, surface mount SOIC, TSSOP and MSOP packages and is also available in the 5-lead SOT-23 package.

Features

Single supply with operation down to 1.8V Low power CMOS technology 1 mA active current typical 1 �A standby current typical (I-temp) Organized as 2 blocks of 256 bytes 8) 2-wire serial interface bus, I2CTM compatible Schmitt trigger inputs for noise suppression Output slope control to eliminate ground bounce 100 kHz (24AA04) and 400 kHz (24LC04B) compatibility Self-timed write cycle (including auto-erase) Page-write buffer for to 16 bytes 2 ms typical write cycle time for page-write Hardware write protect for entire memory Can be operated as a serial ROM Factory programming (QTP) available ESD protection 4,000V 1,000,000 erase/write cycles Data retention > 200 years 8-lead PDIP, SOIC, TSSOP, and MSOP package 5-lead SOT-23 package Available for extended temperature ranges: - Industrial (I): +85�C - Automotive (E): -40�Cto +125�C

*24XX04 is used in this document as a generic part number for the 24AA04/24LC04B devices.

VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS......................................................................................................... -0.3V to VCC +1.0V Storage to +150�C Ambient temp. with power to +125�C ESD protection on all pins...................................................................................................................................................... 4 kV NOTICE: Stresses above those listed under "Maximum ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.

VCC to +5.5V Industrial (I): TAMB to +85�C Automotive (E): TAMB to +125�C Min

Characteristic WP, SCL and SDA pins High level input voltage Low level input voltage Hysteresis of Schmitt trigger inputs Low level output voltage Input leakage current Output leakage current Pin capacitance (all inputs/outputs)

IOL = 3.0 mA, VCC = 2.5V VIN =.1V to VCC VOUT =.1V to VCC = 5.0V (Note) TAMB = 25�C, FCLK = 1 MHz VCC = 5.5V, SCL = 400 kHz Industrial Automotive SDA = SCL = VCC WP = VSS

VCC to +5.5V Industrial (I): TAMB to +85�C Automotive (E): TAMB to +125�C Min Typ Max Units kHz ns Conditions 2.5V VCC 5.5V 1.8V VCC (24AA04) 2.5V VCC 5.5V 1.8V VCC (24AA04) 2.5V VCC 5.5V 1.8V VCC (24AA04) 2.5V VCC 5.5V (Note 1) 1.8V VCC 2.5V (24AA04) (Note 1) (Note 1) 2.5V VCC 5.5V 1.8V VCC (24AA04) 2.5V VCC 5.5V 1.8V VCC 2.5V (24AA04) (Note 2) 2.5V VCC 5.5V 1.8V VCC (24AA04) 2.5V VCC 5.5V 1.8V VCC (24AA04) 2.5V VCC 5.5V 1.8V VCC (24AA04) 2.5V VCC 5.5V 1.8V VCC 2.5V (24AA04)

Characteristic Clock frequency Clock high time Clock low time SDA and SCL rise time (Note 1) SDA and SCL fall time

THD:STA START condition hold time TSU:STA START condition setup time
THD:DAT Data input hold time TSU:DAT Data input setup time

TSU:STO STOP condition setup time TAA TBUF Output valid from clock (Note 2) Bus free time: Time the bus must be free before a new transmission can start Output fall time from VIH minimum to VIL maximum Input filter spike suppression (SDA and SCL pins) Write cycle time (byte or page) Endurance

Note 1: Not 100% tested. CB = total capacitance of one bus line in pF. As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 3: The combined TSP and V HYS specifications are due to new Schmitt trigger inputs which provide improved noise spike suppression. This eliminates the need for a TI specification for standard operation. 4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on Microchip's website: www.microchip.com.


Features

Parameters

Download DataSheet PDF View and Download


Manufacturer information

Warm Hint

What HQEW.NET can offer here?
1. www.hqew.net/product-data provides numerous and various electronic part data-sheet and technology document here., if it can't be shown, Please feel free to ask us for it.
2. www.hqew.net/news provides the latest information of the semiconductor industry or the electronics industry for you.
3. www.hqew.net provides verified suppliers and numerous electronic components for your demand and business.
Any questions you can contact us by email cs@hqew.net.
related datasheet
Browse Alphabetically: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Contact Us

+86-755-83536845

One to One Customer Service

17190417227