Homedatasheet24AA512T

24AA512T Datasheet

I2C->64K to 512K
Share:
Manufacturer

Description

Features, Applications

Part Number 24LC512 24FC512 VCC Range 1.8-5.5V 2.5-5.5V Max. Clock Frequency kHz(1) 400 kHz 1 MHz Temp. Ranges E I

Description

The Microchip Technology Inc. 8 (512 Kbit) Serial Electrically Erasable PROM, capable of operation across a broad voltage range 5.5V). It has been developed for advanced, low power applications such as personal communications and data acquisition. This device also has a page-write capability to 128 bytes of data. This device is capable of both random and sequential reads up to the 512K boundary. Functional address lines allow up to eight devices on the same bus, for to 4 Mbit address space. This device is available in the standard 8-pin plastic DIP, SOIC, DFN and 14-lead TSSOP packages.

Features

Low power CMOS technology - Maximum write current 5.5V - Maximum read current 5.5V - Standby current 100 nA typical 5.5V 2-wire serial interface bus, I2C compatible Cascadable for up to eight devices Self-timed ERASE/WRITE cycle 128-byte Page-Write mode available 5 ms max write-cycle time Hardware write-protect for entire array Schmitt Trigger inputs for noise suppression 1,000,000 erase/write cycles Electrostatic discharge protection > 4000V Data retention > 200 years 8-pin PDIP, SOIC(208 mil), and DFN packages 14-lead TSSOP package Temperature ranges: - Industrial (I): +85�C - Automotive (E): to +125�C

*24XX512 is used in this document as a generic part number for the 24AA512/24LC512/24FC512 devices.

VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS......................................................................................................... -0.6V to VCC +1.0V Storage to +150�C Ambient temperature with power to +125�C ESD protection on all pins...................................................................................................................................................... 4 kV NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.

Industrial (I): Automotive (E): Characteristic A1, A2, SCL, SDA and WP pins: High level input voltage Low level input voltage Hysteresis of Schmitt Trigger inputs (SDA, SCL pins) Low level output voltage Input leakage current Output leakage current Pin capacitance (all inputs/outputs) Min 0.7 VCC 0.05 VCC to 5.5V VCC to 5.5V Max 0.3 VCC 0.2 VCC Units VCC 2.5V VCC < 2.5V VCC 2.5V (Note) TAMB to +85�C TAMB to +125�C Conditions

IOL ma @ VCC = 4.5V IOL ma @ VCC = 2.5V VIN = VSS or VCC, WP = VSS VIN = VSS or VCC, WP = VCC VOUT = VSS or VCC = 5.0V (Note) TAMB = 1 MHz VCC = 5.5V, SCL = 400 kHz VCC = 5.5V TAMB to +85�C SCL = SDA = VCC WP = VSS TAMB to +125�C SCL = SDA = VCC WP = VSS

Industrial (I): Automotive (E): Characteristic Clock frequency Min VCC to 5.5V VCC to 5.5V Max Units kHz TAMB to +85�C TAMB to +125�C Conditions 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC< 2.5V VCC 5.5V 2.5V VCC 5.5V 24FC512 All except, 24FC512 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 5.5V 24FC512 (Note 2) 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 24FC512 1.8V VCC < 2.5V VCC 5.5V 2.5V VCC 5.5V 24FC512 All except, 24FC512 (Notes 1 and 3) 25�C (Note 4)

THD:DAT Data input hold time TSU:DAT Data input setup time

Bus free time: Time the bus must be free before a new transmission can start Input filter spike suppression (SDA and SCL pins) Write cycle time (byte or page) Endurance

Note 1: Not 100% tested. CB = total capacitance of one bus line in pF. As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 3: The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs which provide improved noise spike suppression. This eliminates the need for a TI specification for standard operation. 4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on Microchip's website: www.microchip.com.


Features

Parameters

Download DataSheet PDF View and Download


Manufacturer information

Warm Hint

What HQEW.NET can offer here?
1. www.hqew.net/product-data provides numerous and various electronic part data-sheet and technology document here., if it can't be shown, Please feel free to ask us for it.
2. www.hqew.net/news provides the latest information of the semiconductor industry or the electronics industry for you.
3. www.hqew.net provides verified suppliers and numerous electronic components for your demand and business.
Any questions you can contact us by email cs@hqew.net.
related datasheet
Browse Alphabetically: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Contact Us

+86-755-83536845

One to One Customer Service

17190417227