Homedatasheet25LC320XT

25LC320XT Datasheet

SPI->4K to 64K
Share:
Manufacturer

Description

Features, Applications

DESCRIPTION

Temp. Ranges I I,E The Microchip Technology Inc. 25C320 (25XX320*) are 32 Kbit serial Electrically Erasable PROMs. The memory is accessed via a simple Serial Peripheral InterfaceTM (SPITM) compatible serial bus. The bus signals required are a clock input (SCK) plus separate data in (SI) and data out (SO) lines. Access to the device is controlled through a chip select (CS) input. Communication to the device can be paused via the hold pin (HOLD). While the device is paused, transitions on its inputs will be ignored, with the exception of chip select, allowing the host to service higher priority interrupts.

FEATURES

Low power CMOS technology - Write current: 3 mA maximum - Read current: 500 �A typical - Standby current: 500 nA typical x 8-bit organization 32 byte page Write cycle time: 5 ms maximum Self-timed ERASE and WRITE cycles Block write protection - Protect none, 1/2 or all of array Built-in write protection - Power on/off data protection circuitry - Write enable latch - Write protect pin Sequential read High reliability - Endurance: 100K E/W cycles - Data retention: > 200 years - ESD protection: 4000V 8-pin PDIP, SOIC and TSSOP packages 14-lead TSSOP package Temperature ranges supported: - Industrial (I): +85�C - Automotive (E): to +125�C

PDIP, SOIC SO WP VSS 1 8 VCC HOLD SCK SI HOLD VCC SO 1 TSSOP 8 SCK SI VSS NC WP VSS TSSOP VCC HOLD NC SCK SI

*25XX320 is used in this document as a generic part number for the 25AA320/25LC320/25C320 devices. SPITM is a trademark of Motorola Inc.

VCC.............................................................................................................................................................................7.0V All inputs and outputs w.r.t. VSS.......................................................................................................... to VCC+1.0V Storage to 150�C Ambient temperature under to 125�C Soldering temperature of leads (10 seconds).......................................................................................................+300�C ESD protection on all pins.......................................................................................................................................... 4KV NOTICE: Stresses above those listed under `Maximum ratings' may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for an extended period of time may affect device reliability.

Industrial (I): Automotive (E): Characteristics High level input voltage Low level input voltage Low level output voltage High level output voltage Input leakage current Output leakage current Internal Capacitance (all inputs and outputs) Operating Current Min. 2.0 0.7 VCC -0.3 VCC -0.5 -10 Standby Current TAMB to +85�C TAMB to +125�C Max. 0.8 0.3 VCC Units VCC to 5.5V VCC to 5.5V Conditions VCC 2.7V (Note) VCC< 2.7V (Note) VCC 2.7V (Note) VCC < 2.7V (Note) IOL = 1.0 mA, VCC < 2.5V IOH CS = VCC, VIN = VSS TO VCC CS = VCC, VOUT = VSS TO VCC TAMB = 25�C, CLK = 1.0 MHz, VCC = 5.0V (Note) VCC = 5.5V; FCLK = 3.0 MHz; SO = Open VCC = 2.5V; FCLK = 2.0 MHz; SO = Open VCC = 5.5V VCC CS = VCC = 5.5V, Inputs tied to VCC or VSS CS = VCC = 2.5V, Inputs tied to VCC or VSS

DC Characteristics Param. No. D11 D12 Note: Sym. VIL1 VIL2 VOL VOH ILI ILO CINT ICC Read ICC Write ICCS

Industrial (I): Automotive (E): Characteristic Clock Frequency Min. 100K TAMB to +85�C TAMB to +125�C Max. Units MHz ns VCC to 5.5V VCC to 5.5V Conditions VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V (Note 1) (Note 1) VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V (Note 1) VCC to 5.5V (Note 1) VCC to 5.5V (Note 1) VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V (Note 1) VCC to 5.5V (Note 1) VCC to 5.5V VCC to 5.5V VCC to 5.5V VCC to 5.5V (Note 2) AC Characteristics Param. No. 1 Sym. FCLK

CLK Rise Time CLK Fall Time Clock High Time
Clock Delay Time Clock Enable Time Output Valid from Clock Low Output Hold Time Output Disable Time
HOLD Low to Output High-Z HOLD High to Output Valid Internal Write Cycle Time Endurance

Note 1: This parameter is periodically sampled and not 100% tested. 2: This parameter is not tested but established by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on our website: www.microchip.com.


Features

Parameters

Download DataSheet PDF View and Download


Manufacturer information

Warm Hint

What HQEW.NET can offer here?
1. www.hqew.net/product-data provides numerous and various electronic part data-sheet and technology document here., if it can't be shown, Please feel free to ask us for it.
2. www.hqew.net/news provides the latest information of the semiconductor industry or the electronics industry for you.
3. www.hqew.net provides verified suppliers and numerous electronic components for your demand and business.
Any questions you can contact us by email cs@hqew.net.
related datasheet
Browse Alphabetically: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Contact Us

+86-755-83536845

One to One Customer Service

17190417227