Homedatasheet422OPINB

422OPINB Datasheet

Industrial ISOlated Rs-232 to Rs-422 Converter W/sd Control
Share:
Manufacturer

Description

Features, Applications

Description: The 422OPINB converts unbalanced, full-duplex RS-232 signals to balanced, full or half-duplex or RS-485 signals. The following signals are supported: TD on pin RD on pin 3, RTS on pin 4, and CTS on pin & RD can be configured as DTE or DCE with jumpers & JP2. Specifications: Signals Supported: TD, RD, RTS, & CTS Dimensions: Approximately x 0.68" Data Rate: to 19.2K baud Connectors: RS-232: DB25S (female) and Terminal Blocks RS-422/485: Terminal Blocks Isolation: 2500VAC optical isolation of data signals and ground Power Requirements: RS-232 Side: From at 40mA maximum. Apply at +12VDC and GND. RS-422/485 Side: From at 160mA maximum. Apply at I+12VDC and IGND. Configuration: In RS-485 mode, the driver enable can either be controlled with the RTS line from the RS-232 port or with an automatic circuit triggered by the transmission of data. We refer to these as RTS control and SD (send data) control. They are jumper selectable with jumper JP5. In order for jumper JP5 to have any effect, jumper JP3 must be in the 485 position. When jumper is in the 485 position, the receiver will be disabled during the transmit of data. The other option is to put jumper JP4 in the 422 position enabling the receiver all the time. In RTS mode, the RS-485 driver is enabled when the RTS handshaking line is asserted by your software. You must then disassert RTS in order to turn the RS-485 driver off again. In SD mode, the RS-485 driver is enabled whenever data is transmitted on the RS-232 TD line and disabled approximately one character length after the end of transmission (factory default is set for 9600 baud). If time-out errors occur, the baud rate time-out may need adjustment using the component values in Table & R41 are in parallel with each other. & C10 are also in parallel. If the value or C9 changes from the factory default, you must remove that component from the board before adding In RS-422 mode, jumpers & JP4 should be in the 422 position and JP5 has no effect. In 422 mode the driver and receiver will always be enable for full-duplex communications. There are 4 two-color LEDs for monitoring the supported signals (red = neg. voltage, green = pos. voltage). The board layout has an option for termination resistors (approx. 120 ohm): R9 for the 422/485 RD lines, and R31 for the 422 CTS lines. The RS-422 Standard recommends 24AWG copper conductor, twisted-pair telephone cable with a shunt capacitance of 16pf per foot to 4000 feet. The 232 and 485 power sources must be isolated in order to keep the optical isolation. Power for the 232 side will be connected at +12VDC and GND. The 485 power connects at I+12VDC and IGND. Connect the 422/485 signals TB2 as follows: 2-WIRE MODE 422OPINB: 485 Device: TD(A) & RD(A) (A) or TD(B) & RD(B) (B) or If used: RTS(A) & CTS(A) (A) or RTS(B) & CTS(B) (B) or 4-WIRE MODE 422OPINB: 422/485 Device: TD(A) Receive Data (A) or TD(B) Receive Data (B) or RD(A) --------Transmit Data (A) or RD(B) Transmit Data (B) or If used: RTS(A) Clear To Send (A) or RTS(B) Clear To Send (B) or CTS(A) Request To Send (A) or CTS(B) Request To Send (B) or Table 1. Baud Rate Time-out Replacement Values. Baud Rate Time (ms) Resistor 100K 56K Capacitor (�Fd) C9.1.1.01.01.01.01.01

This product designed and manufactured in USA of domestic and imported parts by

Features

Parameters

Download DataSheet PDF View and Download


Manufacturer information

Warm Hint

What HQEW.NET can offer here?
1. www.hqew.net/product-data provides numerous and various electronic part data-sheet and technology document here., if it can't be shown, Please feel free to ask us for it.
2. www.hqew.net/news provides the latest information of the semiconductor industry or the electronics industry for you.
3. www.hqew.net provides verified suppliers and numerous electronic components for your demand and business.
Any questions you can contact us by email cs@hqew.net.
related datasheet
Browse Alphabetically: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Contact Us

+86-755-83536845

One to One Customer Service

17190417227