Home datasheet 5T9070

5T9070

Clock management
Share:
Manufacturer

Description

Features, Applications
IDT5T9070 2.5V SINGLE DATA RATE 1:10 CLOCK BUFFER TERABUFFER JR.
2.5V SINGLE DATA RATE 1:10 CLOCK BUFFER TERABUFFERTM JR.

Optimized for 2.5V LVTTL Guaranteed Low Skew < 25ps (max) Very low duty cycle distortion < 300ps (max) High speed propagation delay < 2ns. (max) to 200MHz operation Very low CMOS power levels Hot insertable and over-voltage tolerant inputs 1:10 fanout buffer 2.5V VDD Available in TSSOP package

The IDT5T9070 2.5V single data rate (SDR) clock buffer is a single-ended input to ten single-ended outputs buffer built on advanced metal CMOS technology. The SDR clock buffer fanout from a single input to ten single-ended outputs reduces the loading on the preceding driver and provides an efficient clock distribution network. The IDT5T9070 has two output banks that can be asynchronously enabled/ disabled. Multiple power and grounds reduce noise.

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

Symbol VDD Description Power Supply Voltage Input Voltage Output Voltage Storage Temperature Junction Temperature Max �0.5 to VDD +165 150 Unit VI VO TSTG TJ

NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

Symbol CIN Parameter Input Capacitance Min Typ. 6 Max. Unit pF
NOTE: 1. This parameter is measured at characterization but not tested.

Symbol TA VDD Description Ambient Operating Temperature Internal Power Supply Voltage Min. �40 2.3 Typ. +25 2.5 Max. +85 2.7 Unit �C V

Symbol GL Qn VDD GND I/O Type LVTTL PWR Description Clock input Gate for outputs Q1 through Q5. When G1 is LOW, these outputs are enabled. When G1 is HIGH, these outputs are asynchronously disabled to the level designated by GL(1). Gate for outputs Q6 through Q10. When G2 is LOW, these outputs are enabled. When G2 is HIGH, these outputs are asynchronously disabled to the level designated by GL(1). Specifies output disable level. If HIGH, the outputs disable HIGH. If LOW, the outputs disable LOW. Clock outputs Power supply for the device core, inputs, and outputs Power supply return for power

NOTE: 1. Because the gate controls are asynchronous, runt pulses are possible. It is the user's responsibility to either time the gate control signals to minimize the possibility of runt pulses or be able to tolerate them in down stream circuitry.

Symbol IIH IIL VIK VIN VIH VIL VOH VOL Parameter Input HIGH Current Input LOW Current Clamp Diode Voltage DC Input Voltage DC Input HIGH(2) DC Input LOW(3) Output HIGH Voltage Output LOW Voltage Test Conditions VDD VI = VDD/GND VDD VI = GND/VDD VDD = 2.3V, IIN = -18mA Min. 0.3 1.7 VDD - 0.4 VDD - 0.7 Max Unit �A

NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. Voltage required to maintain a logic HIGH. 3. Voltage required to maintain a logic LOW. 4. Typical values are at VDD 2.5V, +25�C ambient.


Features

Parameters

Download DataSheet PDF View and Download


Manufacturer information

Warm Hint

What HQEW.NET can offer here?
1. www.hqew.net/product-data provides numerous and various electronic part data-sheet and technology document here., if it can't be shown, Please feel free to ask us for it.
2. www.hqew.net/news provides the latest information of the semiconductor industry or the electronics industry for you.
3. www.hqew.net provides verified suppliers and numerous electronic components for your demand and business.
Any questions you can contact us by email support@hqew.net.
Other products data
Browse Alphabetically: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Post Buying Request
Latest News & Exhibitons
Contact Us

+86-755-83536845

One to One Customer Service

17190417227