|Single Channel, High Speed Optocouplers Technical Data
15 kV/�s Minimum Common Mode Transient Immunity at VCM V (4503/0453) High Speed: 1 Mb/s TTL Compatible Available in 8-Pin DIP, SO-8, Widebody Packages Open Collector Output Guaranteed Performance from Temperature: to 70�C Safety Approval UL Recognized 3750 V rms for 1 minute (5000 V rms for 1 minute for HCNW and Option 020 devices) per UL1577 CSA Approved IEC/EN/DIN EN 60747-5-2 Approved �VIORM 630 V peak for HCPL-4503#060 �VIORM 1414 V peak for HCNW devices Dual Channel Version Available 0534) MIL-PRF-38534 Hermetic Version Available (55XX/ 65XX/4N55)Applications
High Voltage Insulation Video Signal Isolation Power Transistor Isolation in Motor Drives Line Receivers Feedback Element in Switched Mode Power Supplies High Speed Logic Ground Isolation � TTL/TTL, TTL/ CMOS, TTL/LSTTL Replaces Pulse Transformers Replaces Slow Phototransistor Isolators Analog Signal Ground IsolationDescription
These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance.0.1 �F bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.
These single channel optocouplers are available in 8-Pin DIP, SO-8 and Widebody package configurations. The 6N135, HCPL-0500, and HCNW135 are for use in TTL/ CMOS, TTL/LSTTL or wide bandwidth analog applications. Current transfer ratio (CTR) for these devices is 7% minimum = 16 mA. The HCPL-2502, HCPL-0501, and HCNW136 are designed for high speed TTL/TTL applications. A standard 16 mA TTL sink current through the input LED will provide enough
output current for 1 TTL load and 5.6 k pull-up resistor. CTR for these devices is 19% minimum = 16 mA. The HCPL-4502, HCPL-0452, and HCNW4502 provide the electrical and switching performance of the 6N136, HCPL-0501, and HCNW136 with increased ESD protection. The HCPL-4503, HCPL-0453, and HCNW4503 are similar to the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers but have increased common mode transient immunity of 15 kV/�s minimum at VCM 1500 V guaranteed.
Minimum CMR dV/dt (V/�s) 1,000 VCM (V) 10 8-Pin DIP (300 Mil) Current Single Dual Transfer Channel Ratio Package Package* HCPL-4534 9 Small-Outline SO-8 Single Dual Channel Package Package* HCPL-0453 HCPL-0534 Widebody (400 Mil) Hermetic Single and Channel Dual Channel Package Packages* HCPL-65XX 4N55
*Technical data for these products are on separate Agilent publications. Pin 7, transistor base, is not connected.
Specify Part Number followed by Option Number (if desired). Example: V rms/1 Minute Option* 060 = IEC/EN/DIN EN 60747-5-2 VIORM 630 V peak Option** 300 = Gull Wing Surface Mount Option 500 = Tape and Reel Packaging Option XXXE = Lead Free Option data sheets available. Contact your Agilent sales representative or authorized distributor for information.
*For 6N135/6 and HCPL-4502/3 only. **For HCPL-4503 only. Combination of Option 020 and Option 060 is not available. Gull wing surface mount option applies to through hole parts only.
Remarks: The notation is used for existing products, while (new) products launched since 15th July 2001 and lead free option will use
DIMENSIONS IN MILLIMETERS AND (INCHES). *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION mm (10 mils) MAX.8-Pin DIP Package with Gull Wing Surface Mount Option (6N135/6, HCPL-4502/3)
NOTE: FLOATING LEAD PROTRUSION mm (10 mils) MAX.