CA0555CE Datasheet

Timers For Timing Delays And Oscillator Applications in Commercial, Industrial And Military Equipment


Features, Applications

Timers for Timing Delays and Oscillator Applications in Commercial, Industrial and Military Equipment

[ /Title The CA555 and CA555C are highly stable timers for use in (CA55 precision timing and oscillator applications. As timers, these 5, monolithic integrated circuits are capable of producing CA555 accurate time delays for periods ranging from microseconds through hours. These devices are also useful for astable C, LM555 oscillator operation and can maintain an accurately controlled free running frequency and duty cycle with only C) two external resistors and one capacitor. /SubThe circuits of the CA555 and CA555C may be triggered by ject the falling edge of the waveform signal, and the output of (Tim- these circuits can source or sink a 200mA current or ers for drive TTL circuits. Timing These types are direct replacements for industry types in Delays packages with similar terminal arrangements e.g. SE555 and NE555, MC1555 and MC1455, respectively. The CA555 Oscilla- type circuits are intended for applications requiring premium electrical performance. The CA555C type circuits are tor Appli- intended for applications requiring less stringent electrical cations characteristics. in Part Number Information ComPART NUMBER TEMP. PKG. mer(BRAND) RANGE (oC) PACKAGE NO. cial, 8 Ld PDIP 8 Ld PDIP E8.3 trial 8 Ld PDIP E8.3 and MiliPinout tary CA555C, LM555C, (PDIP) EquipTOP VIEW ment) 8 V+ GND 1 /Author 7 DISCHARGE TRIGGER 2 OUTPUT 3 6 THRESHOLD /Key5 CONTROL RESET 4 words VOLTAGE (Harris Semiconductor, single, timer,


Accurate Timing From Microseconds Through Hours Astable and Monostable Operation Adjustable Duty Cycle Output Capable of Sourcing or Sinking to 200mA Output Capable of Driving TTL Devices Normally ON and OFF Outputs High Temperature Stability. 0.005%/oC Directly Interchangeable with NE555, MC1555, and MC1455


Precision Timing Sequential Timing Time Delay Generation Pulse Generation Pulse Detector Pulse Width and Position Modulation


CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. Copyright � Harris Corporation 1999

Thermal Resistance (Typical, Note 1) JA (oC/W) JC (oC/W) PDIP Package. 100 N/A Maximum Junction Temperature (Plastic Package). 150oC Maximum Storage Temperature Range. to 150oC Maximum Lead Temperature (Soldering 10s). 300oC

CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTE: JA is measured with the component mounted on an evaluation PC board in free air.

PARAMETER DC Supply Voltage DC Supply Current (Low State) (Note 2) Threshold Voltage Trigger Voltage

Trigger Current Threshold Current (Note 3) Reset Voltage Reset Current Control Voltage Level
= 5V, ISINK = 5mA ISINK = 15V, ISINK = 10mA ISINK = 50mA ISINK = 100mA ISINK = 200mA

ISOURCE = 200mA Timing Error (Monostable) Frequency Drift with Temperature Drift with Supply Voltage Output Rise Time Output Fall Time NOTES: = 0.1�F Tested = 15V

2. When the output in a high state, the DC supply current is typically 1mA less than the low state value. 3. The threshold current will determine the sum of the values of R1 and to be used in Figure 4 (astable operation); the maximum total = 20M.

Typical Applications

Figure 1 shows the CA555 connected as a reset timer. In this mode of operation capacitor CT is initially held discharged by a transistor on the integrated circuit. Upon closing the "start" switch, or applying a negative trigger pulse to terminal 2, the integral timer flip-flop is "set" and releases the short circuit across CT which drives the output voltage "high" (relay energized). The action allows the voltage across the capacitor to increase exponentially with the constant = R1CT. When the voltage across the capacitor equals 2/3 V+, the comparator resets the flip-flop which in turn discharges the capacitor rapidly and drives the output to its low state. Since the charge rate and threshold level of the comparator are both directly proportional to V+, the timing interval is relatively independent of supply voltage variations. Typically, the timing varies only 0.05% for a 1V change in V+. Applying a negative pulse simultaneously to the reset terminal (4) and the trigger terminal (2) during the timing cycle discharges CT and causes the timing cycle to restart. Momentarily closing only the reset switch during the timing interval discharges CT, but the timing cycle does not restart.

NOTE: All resistance values are in ohms. FIGURE 1. RESET TIMER (MONOSTABLE OPERATION)



Manufacturer information

Warm Hint

What HQEW.NET can offer here?
1. www.hqew.net/product-data provides numerous and various electronic part data-sheet and technology document here., if it can't be shown, Please feel free to ask us for it.
2. www.hqew.net/news provides the latest information of the semiconductor industry or the electronics industry for you.
3. www.hqew.net provides verified suppliers and numerous electronic components for your demand and business.
Any questions you can contact us by email cs@hqew.net.
Request for Datasheet

  • Part No     :
  • Your Email:
  • Content     :

related datasheet
Browse Alphabetically: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Contact Us


One to One Customer Service