HomedatasheetDFC10U2D12

DFC10U2D12 Datasheet

Dual Output
Share:
Manufacturer

Description

Features, Applications

DESCRIPTION The dual output DFC10 Series provides power solutions to meet commercial and industrial requirements. With power densities above 11 watts per cubic inch (0.67 watts per cm3), overcurrent protection, and five sided shielded case, the DFC10 meets rigorous needs in an industry standard case size. The 120KHz operating frequency of the DFC10 Series allows an increased power density while including adequate heat sinking and input/output filtering. This eliminates the need for external components in most applications. Full overload protection is provided by pulse-by-pulse current limiting on models with 48V input. FEATURES High Power Density, to 11 Watts per Cubic Inch Efficiencies to 79% Fully Isolated, Fully Filtered Design Greater than 700V Isolation Overcurrent Protection Five-Side Shielded Copper Case Ultra Wide Range Input (4:1)

Mechanical tolerances unless otherwise noted: X.XX dimensions: �0.03 inches X.XXX dimensions: �0.005 inches

(1) All parameters measured = 25�C, nominal input voltage and full rated load unless otherwise noted. Refer to the Technical Reference Section for the definition of terms, measurement circuits and other information. Case is tied to the COMMON output pin. The functional temperature range is intended to give an additional data point for use in evaluating this power supply. At the low functional temperature the power supply will function with no side effects, however, sustained operation at the high functional temperature will reduce expected operational life. The data sheet specifications are not guaranteed beyond the case operating range. The case thermal impedance is specified as the case temperature rise over ambient per package watt dissipated.

NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice.

(1) All parameters measured = 25�C, nominal input voltage and full rated load unless otherwise noted. Refer to the Technical Reference Section for the definition of terms, measurement circuits and other information. Noise is measured per Technical Reference Section. Measurement bandwidth is 0-20 MHz. RMS noise is measured over a 0.01-1 MHz bandwidth. To simulate standard PCB decoupling practices, output noise is measured with a 10�f tantalum and 0.01�F ceramic capacitor located 1 inch away from the converter. The converter may be safely operated at any load from zero to the full rating. Dynamic response of the converter may degrade if the converter is operated with less than 25% output load. Load regulation is defined for loading/unloading both outputs simultaneously. Load range to 100%. Cross regulation is defined for loading/unloading one output while the other output is kept at full load. Load range to 100%. Short term stability is specified after a 30 minute warmup at full load, constant line and recording the drift over a 24 hour period.

DFC10 SERIES APPLICATION NOTES: External Capacitance Requirements No external capacitance is required for operation of the DFC10 Series. If a capacitive input source is farther than 1" from the converter, an additional capacitor may be required at the input pins for proper operation. This input capacitor should have an ESR greater than 0.25 ohms. Input capacitors with an ESR less than 0.25 ohms may cause peaking of the input filter and actually degrade circuit performance. External output capacitance is not required for operation, however it is recommended that 10F of tantalum and to 0.1F ceramic capacitance be selected for reduced system noise. Additional output capacitance may be added for increased filtering, but should not exceed 400F.

Typical Performance: (Tc=25�C, Vin=Nom VDC, Rated Load)
LINE INPUT (VOLTS) EFFICIENCY Vs. LINE INPUT VOLTAGE RMS INPUT CURRENT (AMPS)
LINE INPUT (VOLTS) INPUT CURRENT Vs. INPUT VOLTAGE


Features

Parameters

Download DataSheet PDF View and Download


Manufacturer information

Power-One has been acquired by Bel Fuse and is now marketed under Bel Power Solutions.

Power-One has been a leader in high-efficiency "green" power conversion and management solutions, including renewable energy. Power-One's green products include DC-DC converters and power supplies.


Warm Hint

What HQEW.NET can offer here?
1. www.hqew.net/product-data provides numerous and various electronic part data-sheet and technology document here., if it can't be shown, Please feel free to ask us for it.
2. www.hqew.net/news provides the latest information of the semiconductor industry or the electronics industry for you.
3. www.hqew.net provides verified suppliers and numerous electronic components for your demand and business.
Any questions you can contact us by email cs@hqew.net.
related datasheet
Browse Alphabetically: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
Contact Us

+86-755-83536845

One to One Customer Service

17190417227